Furnace Not Heating in Half Moon Bay

Furnace Not Heating in Half Moon Bay

No heat from a gas furnace almost always traces to one step in the ignition sequence failing. The inducer has to run, the igniter has to glow or spark, the gas valve has to open, and the flame sensor has to confirm the flame is lit, and a fault at any one of those steps shuts the whole cycle down as a safety measure. Add a tripped limit switch from restricted airflow, a dead thermocouple on an older wall or gravity furnace, or simply no call for heat reaching the board, and that covers nearly every no-heat call we run. We watch the sequence directly rather than swapping parts on a guess. The detail that matters in Half Moon Bay is the constant marine layer that limits real cooling days and the salt air that eats outdoor equipment.

Housing age and local climate both matter on a no-heat call. Half Moon Bay sits directly on the coast, and the marine layer is not an occasional visitor here, it is the default weather. Summer afternoons rarely climb out of the 60s, real cooling days are the exception, and heating is what actually keeps a house comfortable most of the year. Housing runs from the historic downtown core near Main Street to newer subdivisions up Highway 1 and along the ridge above town. Salt-laden coastal air reaches every outdoor unit here and corrodes coil fins, contactors, and cabinets faster than almost anywhere else we work.

In Half Moon Bay, every gas furnace call includes a carbon monoxide reading and a heat exchanger check, regardless of what brought us out, because that's a safety step we don't skip. The written estimate covers the actual repair, and on an older furnace we'll tell you honestly whether a heat pump conversion is worth putting on the table too. The $99 diagnostic fee is credited toward the repair.

Common causes

Cracked hot surface igniter. The igniter is a thin ceramic element that eventually cracks from repeated heating and cooling cycles. Once it can no longer glow hot enough, the gas valve never gets confirmation to stay open.

Dirty flame sensor. A flame sensor coated with a thin layer of carbon can no longer read the flame properly, so the board shuts the gas valve seconds after ignition, over and over, until the furnace locks out.

Limit switch tripped by a dirty filter. Restricted airflow, often from a dirty filter, lets the heat exchanger run hotter than it should and trips the high-limit switch as a safety response, shutting the burners down. Older coastal homes here often have returns and duct runs sized for a mild climate that never expected much run time.

Failed thermocouple on a wall or gravity furnace. Older wall and gravity furnaces use a thermocouple rather than a flame sensor, and a weakening one shuts the pilot's gas valve even when the pilot is actually lit.

Corroded gas valve or board connection. Age and moisture take a toll on gas valve terminals and board connectors over time. The salt-laden coastal air here corrodes contacts, terminals, and coils noticeably faster than an inland climate would. That can cause an intermittent or complete no-heat fault.

Thermostat or no call for heat. If the call for heat never reaches the board, nothing downstream matters yet. We confirm 24 volts and a real heat call reach the furnace before assuming a mechanical failure.

How we diagnose it

• Confirm a real heat call reaches the control board, so we're diagnosing the furnace and not a dead thermostat or broken low-voltage wire.
• Watch a full ignition sequence: inducer, igniter glow, gas valve, flame sensing, and where in that chain it stops.
• Test the igniter, flame sensor, and limit switch directly with meters rather than swapping parts on a guess.
• On every gas furnace, meter carbon monoxide and inspect the heat exchanger; on older wall and gravity units this is non-negotiable.
• Check filter, airflow, and the gas valve and board connections. The salt-laden coastal air here corrodes contacts, terminals, and coils noticeably faster than an inland climate would. Older coastal homes here often have returns and duct runs sized for a mild climate that never expected much run time.

$99 diagnostic, credited toward the repair. You get a written quote before any work begins.

Furnace Not Heating in Half Moon Bay: common questions

Nearby and related

Furnace Not Heating near Half Moon Bay: Pacifica · San Mateo · Burlingame .

This is usually a furnace repair in Half Moon Bay job. See our furnace repair overview or the Half Moon Bay service area.