Furnace Not Heating in East Palo Alto

Furnace Not Heating in East Palo Alto

No heat from a gas furnace almost always traces to one step in the ignition sequence failing. The inducer has to run, the igniter has to glow or spark, the gas valve has to open, and the flame sensor has to confirm the flame is lit, and a fault at any one of those steps shuts the whole cycle down as a safety measure. Add a tripped limit switch from restricted airflow, a dead thermocouple on an older wall or gravity furnace, or simply no call for heat reaching the board, and that covers nearly every no-heat call we run. We watch the sequence directly rather than swapping parts on a guess. The detail that matters in East Palo Alto is warmer flatland afternoons and older, budget-grade original equipment.

Housing age and local climate both matter on a no-heat call. East Palo Alto sits on the flatland side of the bay, outside the fog belt that cools its Peninsula neighbors, so summer afternoons here run warmer than in Menlo Park or Palo Alto just across the freeway. Most of the housing stock is smaller, single-story homes from the 1950s and 60s, and a lot of it still runs original or budget-grade equipment installed on a tight number. We are straight about what a repair actually costs and when the cheaper fix is the right fix, not just the fastest one to quote.

In East Palo Alto, every gas furnace call includes a carbon monoxide reading and a heat exchanger check, regardless of what brought us out, because that's a safety step we don't skip. The written estimate covers the actual repair, and on an older furnace we'll tell you honestly whether a heat pump conversion is worth putting on the table too. The $99 diagnostic fee is credited toward the repair.

Common causes

Cracked hot surface igniter. The igniter is a thin ceramic element that eventually cracks from repeated heating and cooling cycles. Once it can no longer glow hot enough, the gas valve never gets confirmation to stay open.

Dirty flame sensor. A flame sensor coated with a thin layer of carbon can no longer read the flame properly, so the board shuts the gas valve seconds after ignition, over and over, until the furnace locks out.

Limit switch tripped by a dirty filter. Restricted airflow, often from a dirty filter, lets the heat exchanger run hotter than it should and trips the high-limit switch as a safety response, shutting the burners down. Ductwork on the older, smaller homes here was often sized to the lowest reasonable cost when it went in, not to today's equipment.

Failed thermocouple on a wall or gravity furnace. Older wall and gravity furnaces use a thermocouple rather than a flame sensor, and a weakening one shuts the pilot's gas valve even when the pilot is actually lit.

Corroded gas valve or board connection. Age and moisture take a toll on gas valve terminals and board connectors over time. A lot of the electrical hardware in older homes here is original equipment, well past the age it would already have been replaced on a newer system. That can cause an intermittent or complete no-heat fault.

Thermostat or no call for heat. If the call for heat never reaches the board, nothing downstream matters yet. We confirm 24 volts and a real heat call reach the furnace before assuming a mechanical failure.

How we diagnose it

• Confirm a real heat call reaches the control board, so we're diagnosing the furnace and not a dead thermostat or broken low-voltage wire.
• Watch a full ignition sequence: inducer, igniter glow, gas valve, flame sensing, and where in that chain it stops.
• Test the igniter, flame sensor, and limit switch directly with meters rather than swapping parts on a guess.
• On every gas furnace, meter carbon monoxide and inspect the heat exchanger; on older wall and gravity units this is non-negotiable.
• Check filter, airflow, and the gas valve and board connections. A lot of the electrical hardware in older homes here is original equipment, well past the age it would already have been replaced on a newer system. Ductwork on the older, smaller homes here was often sized to the lowest reasonable cost when it went in, not to today's equipment.

$99 diagnostic, credited toward the repair. You get a written quote before any work begins.

Furnace Not Heating in East Palo Alto: common questions

Nearby and related

Furnace Not Heating near East Palo Alto: Palo Alto · Menlo Park .

This is usually a furnace repair in East Palo Alto job. See our furnace repair overview or the East Palo Alto service area.